Project: Refinish Lane Acclaim tables, part 2

OK, picking up where we left off on the project last time --

Next for the two-tiered end table, I hit a few spots with 220 grit sandpaper, and then went over the whole table with extra fine 0000 steel wool.  Then I wiped all areas down with mineral spirits and let the table dry, which didn't take long.  Here's what it looked like at that point:

As you can see, the side wood and dovetail areas are much lighter from the stripper.  I debated with myself and decided that I would not re-stain at first.  

I've had good success with Howard's Restor-A-Finish.  This stuff will cover up small scratches and bring back some color, so instead of using a stain, I wiped the whole table down with the Walnut variety of Restor-A-Finish and let that sit for about an hour.  

Then I wiped off the excess, and at that point, this is what it looked like:

The light areas are still not nearly as dark as they were before. 

But honestly, I like it this way, so that's all the staining work I'm doing.  Sorry if you were hoping I would figure out how to get it back to the exact finish it was originally.  Oh well.  My table.  :-D

To finish the table off and protect it, I'm using  this Minwax product.  

I like that this stuff wipes on. No brushing or spraying to run or streak.  Grab a clean cotton cloth, wipe it on, let it dry, do a once over with extra fine steel wool and wipe down the whole table again so you don't have little steel wool fragments laying around, then repeat with a second or third coat of the Wipe-On Poly and I'm  done - except for masking off the leg bottoms and adding a coat of black paint, which is how they were originally.

So here's the two-tiered end table after two coats of poly and with the black paint renewed on the legs.

(That lump on the chair on the left is just Miss Patchelina - she thinks that Z chair is hers. Ha!  She is sooooo wrong.)

I'll be finishing the coffee table the same way, and once that's done look for final photos of that table too.

Overall I'm happy with how these turned out.  

If I wanted the tables to be darker as original, I would suggest  not using strippers but lightly sanding and refinishing with a dark stain like walnut, and probably using multiple coats to get the darker look.

Project: Refinish Two Lane Acclaim Tables, Part 1

OK, so back in the summer I scored this great Lane Acclaim coffee table at an estate sale for a nice price because it had some serious wear on the finish.

I've been biding my time on tackling this project, but the other day I happened to find a two-tier Lane Acclaim end table at the nearby thrift shop/consignment shop, and it had similar finish issues but also was very solid.  Together I have only about $80 in these tables, so I think I'm doing pretty good.  Now to see if I can get them looking good again.

I've picked up some good information on these from several sources, including Mr. Modtomic, and from this link at JetSetModern.  I learned that the dovetailing at the ends of the tops is very think veneer, and so is the center section of the table tops.  When I say thin, we're talking almost paper thin.

I ran across someone on Flickr who did a lot of sanding and then applied multiple coats of lacquer to make her's look like new, so that was an option I for me, but man I hate sanding.  I do it, but I hate it.  And sanding this thin veneer is risky, you can cut right through it if you're not careful.

I figured I would first try a variety of stripper I've been using a lot (I went through a whole jug of the stuff on the metal outdoor chairs project).

It really works great and it's orange-based so it's not too harsh to work with.

The coffee table's one end was practically bare so I figured I would try a little of the orange stripper around that area.  After you let this stuff work for a while (usually 20 minutes is enough) you can scrape it off with a razor blade.  So I tried that, and I knew right away that I liked the results, so I did the whole coffee table top this way.

What I scraped off was sort of like molasses, but underneath I had a pretty nice looking result.  I did have one spot where the razor blade caught the veneer and took it right off, leaving an inch-long splinter that I had to glue down again.  That's how I know how thin this veneer is.

The razor also left some scratches in places, so I will have to do some sanding, and that light sanding should help ensure that I've gotten all traces of the stripper removed from the wood.

I decided to wipe down the remaining areas with mineral spirits after I had wiped off as much of the stripper as I could.

A couple of rounds of wiping with the mineral spirits showed where I still had some old finish to remove, so I hit those spots again with the stripper.

For the two-tiered end table, I decided to skip the razor blade and just wipe off the stripper with paper towels and 0000 steel wool.  This worked great, and I did the same with the legs and frame underneath.

That brought me to this point. that's where I'll pick up with my next post to finish these up.